陈学群, 张万灵, 陈珊, 刘建容, 曹国良, 李国明. 经济型耐腐蚀钢中氧作用的研究[J]. 工程科学学报, 2021, 43(7): 960-965. DOI: 10.13374/j.issn2095-9389.2020.04.29.001
引用本文: 陈学群, 张万灵, 陈珊, 刘建容, 曹国良, 李国明. 经济型耐腐蚀钢中氧作用的研究[J]. 工程科学学报, 2021, 43(7): 960-965. DOI: 10.13374/j.issn2095-9389.2020.04.29.001
CHEN Xue-qun, ZHANG Wan-ling, CHEN San, LIU Jian-rong, CAO Guo-liang, LI Guo-ming. Effect of oxygen on economical corrosion resistant steel[J]. Chinese Journal of Engineering, 2021, 43(7): 960-965. DOI: 10.13374/j.issn2095-9389.2020.04.29.001
Citation: CHEN Xue-qun, ZHANG Wan-ling, CHEN San, LIU Jian-rong, CAO Guo-liang, LI Guo-ming. Effect of oxygen on economical corrosion resistant steel[J]. Chinese Journal of Engineering, 2021, 43(7): 960-965. DOI: 10.13374/j.issn2095-9389.2020.04.29.001

经济型耐腐蚀钢中氧作用的研究

Effect of oxygen on economical corrosion resistant steel

  • 摘要: 为了冶炼不同氧含量的碳素船体钢,通过机械性能试验和周浸试验研究了钢中氧含量对钢材腐蚀性能和机械性能的影响。结果表明,在连铸生产许可的氧范围内,随着钢水脱氧程度的减弱,钢中氧质量分数增加,钢材的平均腐蚀率略有下降,而耐点蚀性能有较明显增强,变化曲线的高氧端比低氧端平均点蚀深度下降约22.7%。弱脱氧钢的机械性能符合规范要求,可达到D级钢水平。分析认为,氧提高钢材耐蚀性的原因主要是固溶氧可提高铁的热力学稳定性,提高了蚀孔内铁的腐蚀电位,降低了蚀坑扩展速度。氧作为耐蚀元素应用可以显著降低耐蚀钢的成本,提高经济性。

     

    Abstract: Carbon steels are widely used structural materials in vessel and marine engineering. Many studies acknowledge that the pitting corrosion of these materials are heavily subject to their metallurgic factors. Although much attention has been paid on inclusions and microstructure, little had been dealt with metallurgical processing including deoxidizing degrees. Deoxidization is one of the most important processes in steelmaking. Stronger deoxidizing degree helps to improve steel’s mechanical property and welding property. However, some studies demonstrated that weaker deoxidizing degree tends to improve pitting corrosion resistance. Manufacturing ordinary structural steels nowadays have been changed from mould casting to continuous casting. However, the deoxidizing degree of continuous casting steel may be different due to different deoxidization techniques. Particularly, the oxygen content in current steels has a fairly low level, which may be harmful to pitting corrosion resistance of steels. In this study, the influence of oxygen content in carbon hull steels on corrosion and mechanical properties of steel was investigated by mechanical properties tests and alternate immersion test. Results show increased oxygen content when there is duction of deoxidization of molten steel in the range permitted by continuous casting. Interestingly, the average corrosion rate of steel slightly decreases and an obvious enhancement of resistance to pitting is observed. The average pit depth corresponding to the high oxygen side of the pit depth-oxygen curve is about 22.7% lower than that of the low oxygen side. The mechanical and cold bending properties of tested steels are able to meet technical code requirements and can reach the level of Grade D hull steel. Findings of this study suggest that solid solution oxygen in steel plays a major role in improving pitting resistance. It can enhance the thermodynamic stability of iron, elevate the corrosion potential of the iron in the pit, and reduce the pitting rate. Therefore, using oxygen as a corrosion resistant element is an economic strategy to reduce the cost of corrosion resistant steel.

     

/

返回文章
返回