李国平, 裴海祥, 李建春, 张寿禄. σ相对S32760超级双相不锈钢组织和性能的影响[J]. 工程科学学报, 2016, 38(3): 364-370. DOI: 10.13374/j.issn2095-9389.2016.03.010
引用本文: 李国平, 裴海祥, 李建春, 张寿禄. σ相对S32760超级双相不锈钢组织和性能的影响[J]. 工程科学学报, 2016, 38(3): 364-370. DOI: 10.13374/j.issn2095-9389.2016.03.010
LI Guo-ping, PEI Hai-xiang, LI Jian-chun, ZHANG Shou-lu. Influence of σ phases on the microstructure and properties of S32760 super duplex stainless steel[J]. Chinese Journal of Engineering, 2016, 38(3): 364-370. DOI: 10.13374/j.issn2095-9389.2016.03.010
Citation: LI Guo-ping, PEI Hai-xiang, LI Jian-chun, ZHANG Shou-lu. Influence of σ phases on the microstructure and properties of S32760 super duplex stainless steel[J]. Chinese Journal of Engineering, 2016, 38(3): 364-370. DOI: 10.13374/j.issn2095-9389.2016.03.010

σ相对S32760超级双相不锈钢组织和性能的影响

Influence of σ phases on the microstructure and properties of S32760 super duplex stainless steel

  • 摘要: 通过对含W的S32760超级双相不锈钢不同温度时效热处理研究σ相的析出行为.用扫描电镜和透射电镜分析σ相的形貌和化学组成,并研究σ相对力学性能和耐腐蚀性能的影响.在850~1000℃之间,实验钢析出大量由Fe-Cr-Mo-W组成的具有正方结构的σ相,钢板强度和硬度高,塑性差,延伸率低于4%;1050℃时仍存在少量析出,虽然延伸率大幅度提高至31.1%,但冲击韧性离散度高,冲击功偏低;直至1080℃,σ相才能完全溶解至基体中,抗拉强度为640MPa,延伸率为35.5%,纵、横向冲击功平均值分别达到217J和110J.随时效热处理温度升高,点蚀电位提高,点蚀失重率不断下降,1080℃热处理的试样点蚀电位高达1246mV.该试样在50℃的3.5% NaCl溶液中腐蚀失重率也仅为0.005~0.007g·m-2·h-1.

     

    Abstract: The precipitation behavior of σ phases in W-containing S32760 super duplex stainless steel was studied by aging treatment experiments. The morphology and chemical composition of the σ phases were investigated by scanning electron microscopy and transmission electron microscopy. The effects of the σ phases on the mechanical properties and corrosion resistance of the stainless steel were analyzed additionally. The σ phases composed of Fe-Cr-Mo-W have a tetragonal structure and abundantly precipitate at 850-1000℃ in the stainless steel with quite high strength and hardness and extremely poor plasticity,for example,the elongation is lower than 4.0%. There are still a few of σ phases at 1050℃,though the elongation increases to 31.1%,the values of impact toughness are discrete,and the average impact energy is low. Until 1080℃,the σ phases completely dissolve to the matrix. The tensile strength and the elongation are 640 MPa and 35.5%,and the longitudinal and the transverse impact energies averagely reached to 217 J and 110 J,respectively. As the treatment temperature increasing,the pitting potential(Eb) improves,and the mass loss rate of pitting corrosion decreases. The pitting potential of the stainless steel treated at 1080℃ is up to 1246 m V,while the mass loss rate decreases only to 0.005-0.007 g·m-2·h-1 when being soaked in a 3.5% Na Cl solution at 50℃.

     

/

返回文章
返回